3D printing
3D Print Terrain Infill: Settings for Ruined Walls and Props
How much infill tabletop terrain needs, why perimeters matter more, which pattern to pick and how many top layers to use, with sources from slicer docs.
Most 3D printed terrain needs very little infill. The Prusa Knowledge Base says most models print well with 10 to 15 percent infill and that you will rarely need more than 30 percent. For ruined walls, corners and props, the setting that decides whether a piece survives the gaming table is the number of perimeters, not the infill. The settings that decide how a piece looks are the number of top layers and the layer height.
This guide explains why, which infill pattern to pick, and gives a short list of starting settings for walls, floor tiles and small props. Every number comes from slicer documentation (Prusa and Bambu Lab) or from the print notes of the terrain generator we make.
Why infill matters less on terrain than you think
Infill is the pattern the slicer prints inside a model, between its outer walls. The Prusa Knowledge Base says infill affects print speed, strength, filament use and even the look of the object. On strength, it is direct: "The strength of a model is mostly defined by the number of perimeters (not infill)." Infill still helps with compression resistance, but if you want a stronger print, the advice is to add perimeters.
Terrain makes this effect larger, because many terrain pieces are thin. Take a ruined wall that is 8 millimetres thick. With three perimeters on each side, a large part of that thickness is already perimeters, and around windows, doorways and broken edges the wall is thinner still. In a thin section there is little or no space left inside, so the infill percentage you type changes almost nothing there.
You can see this yourself before you print:
- Slice the piece with your usual settings.
- Open the slicer preview and move the layer slider to the middle of the wall.
- Look at the colours for perimeters and for sparse infill.
- If the wall is almost all perimeters, changing infill from 15 to 30 percent will not make it stronger. Add a perimeter instead, or make the wall thicker in the model.
Thick parts are different. Pillars, rubble piles, bases and blocky props have real space inside, and there the infill decides how much filament and time the piece takes.
How much infill for each kind of terrain piece
Use these as starting points, then adjust after a test print. They follow the ranges in the Prusa infill article and the perimeter advice above.
| Piece | Infill | Perimeters | Notes | |---|---|---|---| | Thin walls and ruins | 10 to 15 percent | 3 | Most of the wall is perimeters; check the preview | | Pillars, rubble piles, thick bases | 10 to 15 percent | 2 to 3 | Infill fills the inside and supports the top | | Floor tiles and flat tops | 15 percent or a little more | 2 to 3 | The large flat top needs support under it | | Small props (barrels, crates) | 10 to 15 percent | 2 to 3 | Small parts are mostly perimeters anyway |
Three perimeters for walls is what the RuinKit print notes ask for with a 0.4 millimetre nozzle. Prusa's own print profiles always use a minimum of two perimeters.
What about 100 percent infill? Prusa says you can do it, and that the pattern is then forced to rectilinear, but also that 100 percent infill can have a negative effect on how the object looks. For terrain it mostly adds weight, time and filament.
And 0 percent? Prusa says a model can be printed hollow if its top closes gradually, but does not generally recommend it. Wall tops and floor tiles have flat tops, so they need some infill under them.
Which infill pattern to choose
Both PrusaSlicer and Bambu Studio offer many patterns. For terrain, four are worth knowing. The descriptions below are from the Prusa infill patterns article and the Bambu Lab wiki.
- Gyroid. Prusa calls it its favourite: it is three-dimensional, gives equal strength in all directions and prints fairly quickly. Bambu Lab adds that slicing takes longer, the G-code file is larger, and at high densities and high speed it can cause strong vibration. At terrain densities this is a good default.
- Adaptive cubic. It changes density with the distance from the walls. Prusa says it gives shorter print time and lower filament use while keeping good support for top layers, with about one quarter less material than rectilinear. Useful for pillars, bases and other thick pieces.
- Lightning. A branching structure that gets denser towards the top surfaces, only to support them. Prusa says it saves even more material than support cubic. Bambu Lab describes it as ideal for aesthetic models that do not need strength. Good for props that sit on the table and are rarely picked up; less good for walls that get knocked over.
- Grid. Prusa says it is more solid and has better layer adhesion than rectilinear, but the nozzle passes over the crossings, which can cause noise or even a failed print. Bambu Lab notes the same risk at high speed. If you have had problems with grid, switch to gyroid.
Rectilinear is one of the fastest patterns and, according to Prusa, the only one recommended for 100 percent infill. It is a fine choice if print time matters more to you than anything else.
Top layers and layer height: what you actually see
On terrain, the visible surfaces are the wall tops, the edges of broken bricks and the top of floor tiles. Their quality depends on two settings more than on infill.
Top solid layers. Prusa says the tops and bottoms of models are filled with solid layers and suggests at least three top layers. The number depends on layer height: with 0.3 millimetre layers use three top layers, with 0.1 millimetre layers use nine. If you see gaps or a rough surface on the top of a floor tile, add top layers before you add infill. Infill supports the top layers; it does not replace them.
Layer height. Prusa explains the trade-off plainly: taller layers shorten print time but make layers more visible, and small layers such as 0.10 millimetre give more detail but take longer. It does not suggest going below 0.10 millimetre, because the gain is small and the time cost is large. The maximum layer height should be below 80 percent of the nozzle diameter, which is about 0.32 millimetre for a 0.4 millimetre nozzle. The RuinKit print notes suggest 0.12 to 0.16 millimetre layers for walls, because brick and stone textures show layer lines easily.
Save time without losing detail. PrusaSlicer has a "Combine infill every X layers" option. It prints the infill with thicker layers than the perimeters. Prusa's example: with 0.1 millimetre layers and infill combined every 3 layers, the infill is printed at 0.3 millimetre. The limit is again your nozzle diameter. On thick terrain pieces printed at a fine layer height, this can save time while the outside keeps its detail.
Resin printers. The settings in this guide are for filament (FDM) slicers. For resin, follow the print notes of the model's designer; the generator described below, for example, says to print its pieces flat on the plate with no hollowing needed.
A free generator for terrain that prints with these settings
If you need the terrain itself, not only the settings, RuinKit is a free tool from Pacix Labs. It runs in the browser with nothing to install and generates ruined walls, corners, pillars and rubble piles for 28 to 32 millimetre games, in brick, stone block or industrial panel textures. You set length, height, thickness, brick size and damage level, then download an STL. The page says the files are closed, manifold meshes. There are also period props (barrel, crate, ladder, well, hand cart and others) in 15, 28, 32 and 54 millimetre scales, an optional base strip and optional holes for 5 × 2, 6 × 3 or 8 × 3 millimetre magnets.
Its print notes match the advice above: print walls standing up as exported, no supports needed for walls, 0.12 to 0.16 millimetre layers, 0.4 millimetre nozzle and three walls (perimeters). The page says the cart and the well print best with tree supports or in resin. A free 5-piece sampler can be downloaded from the page as a ZIP file with a print guide.
You do not need a generator to use this guide. Model-sharing sites host terrain files from many other designers, free and paid, and you can also model your own pieces in any CAD program. Whatever the source, read the designer's print notes first and slice one test piece with the settings above.
Checklist before you slice terrain
- Infill at 10 to 15 percent for most pieces; rarely above 30 percent.
- Gyroid as a default pattern; adaptive cubic for thick pieces; lightning only for props that are not handled much.
- Three perimeters for walls; add perimeters, not infill, if pieces break.
- At least three top layers, more at small layer heights (nine at 0.1 millimetre).
- Layer height between 0.12 and 0.16 millimetre for textured walls; never above 80 percent of the nozzle diameter.
- Check the slicer preview: if a wall is all perimeters, the infill setting does not matter for it.
- Print one test piece before a full table, then change one setting at a time.
Frequently asked questions
What infill percentage should I use for 3D printed terrain?
The Prusa Knowledge Base says most models can be printed with 10 to 15 percent infill and that you will rarely need more than 30 percent. Terrain is usually decorative and handled gently, so the low end is a sensible place to start. If pieces break, add perimeters before you add infill.
Can I print terrain with 0% infill?
Prusa says a model can be printed hollow if its top closes gradually, but it does not generally recommend it. Flat tops, such as wall tops and floor tiles, need infill under them to hold the top layers. Most terrain is safer with a low infill than with none.
Does more infill make terrain stronger?
Only a little. Prusa states that the strength of a model is mostly defined by the number of perimeters, not by infill, although infill helps with compression resistance. For walls that snap at the base, more perimeters is the first change to try.
Which infill pattern is good for terrain?
Gyroid gives equal strength in all directions and prints fairly quickly, according to Prusa. Adaptive cubic uses about one quarter less material than rectilinear while still supporting the top layers. Lightning saves the most material but Bambu Lab describes it as suited to models that do not need strength, so keep it for props that are not handled much.